|
|
| As
with most other websites on the internet, the search facility
etc on this site uses Javascript. If you have any problems
navigating, please use our
SITE MAP
to search the website. |
 |
|
|
|
Window
Graphics
|
Firstly
ensure that the glass is clean, (free from dust,
wax, grease etc.), and try to avoid working in
extremely hot or cold temperatures. If large vinyls
are to be fitted, it may help if two people work
together.
You can either fit the vinyl wet or dry, (see
below.) Wet application should mainly be used
on larger items, or if you are new to the process.
(The water helps to make repositioning easier.)
Dry application is quicker, but much more care
must be taken to avoid air-bubbles etc appearing
in the vinyl.
|
 |
Wet
application:
Moisten the glass with water, either using a spray-bottle
or sponge/non-fluffy cloth etc. (a very slight
amount of mild washing-up liquid can be added
if required, though it's not normally essential.)
Dry application:
No need for any the above!
|
Carefully
remove the vinyl graphics by lifting up the 'application
tape' from the 'silicon release paper backing',
(making sure that all the vinyl decals are lifted
up with it), avoiding finger marks on the vinyl
itself. Larger sheets may need two people to work
together. One to hold the application tape/graphics
by two corners, and the other to carefully peel
back the white, glossy silicon backing paper. When
it's nearly all removed the second person should
then take hold of the remaining two corners of the
tape/graphics. It can now be taken over to the vehicle,
keeping it taut as you go, and avoiding fabrics,
clothing etc., otherwise dust and fluff can be attracted
to the static of the vinyl.
(Note: If any parts of the graphic refuses to
lift, simply place the whole graphic (still on its
backing) on a firm surface and rub over the 'application
tape' with your finger nail to press the section
back against the silicon paper. Also see the 'Problem
solving' section below for further details.)
|
 |
 |
Tack
the graphics gently onto the glass, using a tape
measure at this point if required. If it needs repositioning,
quickly pull it off and try again.
|
|
Once
you are happy with the positioning, start to flatten
it to the surface using a plastic squeegee, firm
credit card or a cloth. It may help if you hold
the graphics slightly away from the surface as you
proceed. Working from the centre outwards, press
down the vinyl pushing the water/air out towards
the edges. Try to avoid letting the graphics slide
about as you are working.
|
 |
 |
If
fitted dry, the application tape can now
be carefully removed by peeling away from the panel
at 180 degrees, (flat on itself.) Note: If
fitted using the 'wet application' method,
you may need to wait for quite a while before removing
the application tape. (It is impossible to give
a precise timescale as no two situations are the
same. Central heating, cold exterior temperatures,
inticacy of the design, and even the brand /concentration
of any added washing-up liquid can all have an affect
on the drying-time. It's best if you can check every
so often to see if the application tape can be carefully
removed. If the graphics have not yet adhered to
the glass, then it will need to be left longer.)
|
|
Once
fitted, check for any water/air bubbles. If they
won't push out, use a pin or scalpel blade to carefully
pop them, then squeeze out the water/air. (Note:
It's always best to prick one edge of the bubble,
rather than the centre. You can then push the water/air
out towards the pinhole.) Job done!
|
 |
|
|
Please
do not wash or polish windows for at least one week.
(Thereafter,
normal window cleaning can be done, but care must always
be taken, especially with dusters, around the decals.)
|
|
Notes
on removal of old self-adhesive vinyl:
Use an
electric heat gun or hot hair dryer to gently warm
the vinyl to be removed, taking care not to overheat any
glass or painted surfaces etc. Carefully lift one
corner of the vinyl, using a blade or window-scraper etc.,
and peel away the vinyl. Repeat on all required sections
until completely removed. Any slight glue residue left
behind can easily be removed using a 'Tar and Glue Remover',
(which is available from most car accessory shops), or
white spirit.
Important: Please take care
when using the extremely hot heat guns, especially where
glass, paintwork and other similar surfaces are concerned.
They are quite safe and efficient to use, providing care
is taken. Always hold the heat gun 'well away' from the
surface, and your own hands, while you work. Just enough
warmth to allow the vinyl to be softened is all that is
necessary. Always handle heat guns with care and keep
them away from children. Also always allow them time to
cool down afterwards before storing away.
|
|
These
instructions, as well as any others on this site, are
merely intended as a guide to fitting our various products.
Although we endeavour to be as efficient as possible with
our instructions, and include as many details as we can,
we cannot be held responsible for any problems, damages
or indeed injuries, which might occur. As with all DIY
projects, the person or persons carrying out the work
is/are held responsible. ( Terms
and Conditions )
|
|
 |
